Видео

Dude I literally was going by your fucking step by step by your you should put that in writing or say that because there's going to be times when people are falling along with your video and doing it at the same time as you like me and then she got every mother fucking at the end of the world but most of this video was completely until the end of the video that was helpful but

What would be interesting is to submerge two pieces of stainless in water, with and without. Measure the resistance of each

Good on ya mate

G'day mate, what flux do you use to braze aluminium?

I never understand combonation pliers. They’re an inferior slip joint plier and an inferior lineman’s.

also tip use rubbing alcohol to spray on the blade when cutting it will super cool the blade DONT USE FORCE mild gentle pressure will save breaking teeth

awesome bag, but have a slight problem with it is that it does not made the shoulder strap adjustable

Glad I watch this seeing that aluminium melt that quick I was like holy crap

Nice video and and advice for the spacing. I have a 60 year old band saw at my work and it's such a burden trying to get it to cut straight. I think I've talked my boss into getting a setup similar to yours and now I will be able to cut angles as well.

Hey I need the back bushing for my drill

It took you so long to get into this i just bought a new battery instead

rolled my aluminium motorbike (tow behind) trailer 😢. Panel beating done, 🤞 now time for the aluminium braising. Not structural and will be painted afterwards. Might try a piece of stainless underneath the hole as a backer. Go video and no fluff.

Cheers for that mate. 👍

Why are you slamming tools down like they are sacks of cement? Are you a bit uncultured?

Its not a Makita knock off, its just a cheap unbranded tool, which happens to be quite good, i have one of these. Makita is probably made in China as well so are the batteries, everything comes from China nowadays.

Fuck yeah!!!

Tool bag tour is due surely or home made tools 🤙

Great video. Makita have eight plants and one of them is in China. Probably the real Makita angle grinder is actually made in China anyway. Knowing how the Chinese operate that Chinese plant is making the knock offs...

Can I use the sandpaper wet? Thanks

You can buy a hook and loop conversion disc for the circular disc. This will allow you you to use normal 150mm sanding discs and change grits to your heart's content rather than melting the bloody glue and stripping it off of the disc every few weeks.

I used the Lenox plier wrench variant and they were decent, sloppy af and seemed to be assembled in the dark but they worked ok so I bought the Lenox cobra copy and have been using them for a few 18 months or so and they’re decent but I will say the materials used and build quality is night and day…the teeth on the Lenox raptor clone have worn so much it’s almost unbelievable for the little amount of work they’ve put in, basically the alloy they’re using in the Lenox is just garbage and wears way way faster…. my cobras teeth look damn near new after two years, the edges of the teeth are just slightly rolled over and the Lenox are toast, barely grip anymore and look like they’ve filled down so if you plan on using them regularly…better to just bite the bullet and buy once cry once cuz the difference is night and day imo

2 tubes put together i think they usually fill a valley ..suggest sharpening the edge

" Ah Lou Mini Um" Say it with me now. 😂 Its "Al Loom In Um"

Welding is all about feeling and the right angel☝️

if you applied this coating to a mesh and then poured an oil-water mixture over it, would the oil go through the mesh still and the water be repelled? Is this coating oleophillic?

Been using these with a pneumatic drill and rotarbroach for the last 2 years on a gas rig. Still can't believe no one seems to use them in mining. Mag drills are still better when you can use them, but these are a life saver in other situations.

Is this thing still alive?

I wish the default speed was high, instead of low.. The little speed button drives me nuts... Anyone know how to change default speed to high or bypass low altogether?

Please, what about Facom, Milwaukee or Olfa 7inch scissors? aren't they as good, if not better than Knipex? Has anybody tried any of these please?

You're not supposed to put direct flame on the brazing rods

Hows it holding up a couple years later?

Hey bro im having trouble getting this too work, it just idles up and down, do you have any tips?

You need to use bronze rods to braze with, you can't braze with aluminum rods.

Is there risk to ruining the newer style batteries if I remove he my as one comment said? Batteries are damn expensive so wouldn’t be worth it if there’s a chance of killing newer style batteries?

Boroscope has a VERY short focal length.

my light is strobing when i turn it on, it used to stop strobing after a minute, then two, then five, then ten... now it doesnt seem to stop at all. i gave up for a week but i shouldnt keep using the pathetic desk light ive put in its place. i hope this has a lead

Ayy welcome back

Great review Finn, technology keeps evolving and people naturally doesn’t like change but once it gets through a period of transition the new blades could move into the industry right across the board. Great work and reviewing the next generation 👊🏼👊🏼

Fiiiiiiin where have you been mate, I’ve been trying to play it cool but I was genuinely concerned you weren’t coming back haha hopefully you’ve got some videos coming our way this year

Welcome back Finn. 👍🏻

Finn's back boys!

Woah, new Finn content. Hell yea.

ive always found cordless grinders to be gutless too. thanks for sharing your thoughts on this one :)

2024 Beehive tour? 👀

Used bosch professional grinders in the past and them anti vibration handles are great. Suggest anyone with a grinder to invest a few quid in one as most grinders use the same thread for handle attachments

aluminium is a good conductor of heat. heat the job just to the side of the join so you can rub the brazing rod on the job out of the main flame. braze tends to flow towards the flame/more heated area. turn your map flame down for thinner materials. propane works. aluminium is very reactive and oxidises really fast (21% oxygen in the air) so prep thoroughly by sanding/stainless wire brush etc to expose unoxidised metal and heat to the sweet spot temperature quickly and braze promptly. If it fails to flow easily and quickly then let it cool and prep surface again as the surface may have reoxidised. practice on similar scrap. first. my first attempts were terrible.

Which screw size do philips #1 , #0 Screwdrivers fit?

Use cutting fluid when cutting thick bar and you should be fine mate. I always wondered about putting a stone blade in my flexvolt dewalt mitre saw but since its a 1200 quid saw I've never had the balls to do it. I am tempted to make a clamp and arm that I can attach a cheap large angle grinder to and make a solid guard so that I can cut through steel as though it's a mitre saw!

I wasn't even thinking about subscribing til the end and you know what fuck you. I will. You just persuaded me to buy another fucking ratchet